GR202系列高溫高壓染色機/GR202-5KG～600KG高溫拉鏈染色機

安裝與調試
*布置安裝位置時，除考慮機器本身機械安裝的空間外，還要考慮染機周?chē)膱?chǎng)地，是否能滿足裝缸、出缸、布放紗籠等要求以及是否有利于今后保養工作的進行。
*機器可按下法找平：氣動打開缸蓋、在缸口處，十字交叉水平尺檢驗水平，最后緊固地腳螺栓。
*排液口和卸壓管的下方，均應開有地溝，使廢液沿著地溝順利排出，避免濺溢地面，腐蝕機器支架，地溝方位用戶根據現場自行決定。
*調試前應檢查各部位的螺栓（特別是泵底架的螺栓或調節絲桿）是否緊固，帶有聯軸器的泵一定要使電機與泵軸同心。
*電氣設備及壓縮空氣控制線路的安裝位置，均由使用單位根據廠房具體情況自行決定，但應方便操作，不影響紗籠的搬運。（注意：電纜切勿靠近熱源）
操作運轉
操作前的準備工作：
*檢查各氣動閥和電氣位置，確使它們在裝設位置與控制柜上各按鈕開關一一對應。并使泵的轉向正確。
*用肥皂液蘇打溶液或其它適宜的洗滌劑對機器進行*清洗。
*為避免可能的殘留污物給試驗原料造成污斑，為此試驗時先染深色，后染淺色。
*染槽內通入所需要軟水，將裝有被染物的染籠吊入染槽后加熱到40-50℃煮煉十分鐘，取出染籠排液。
操作轉注意事項：
禁止在受壓狀態下啟蓋或常壓狀態下閉蓋排液。
主泵與輔泵絕不允許在缺水情況下啟動，泵在運轉中如發生異常聲響或其它故障時，應立即停車檢修。
特別注意：
請嚴格遵守當地勞動部門或鍋爐壓力容器安全主管單位的規章制度和法規：并接受上述部門的監督和檢查。
嚴禁在80℃以上開啟鍋蓋或各管口，以免發生事故。

Installation and adjustment
*When arranging installation positions,besides considering the self mechanical installation space of the equipment,the surrounding site of dyeing machine shall also be considered so as to ensure the cylinder lilling ,cylineer discharging and sarong layort,etc work wioo be favorable to the furure maintenance.
*The machine can be levelve acfording to following mathod:Open the cylinder coer pneumatically.
Place the horizontal ruler in cross directions on the cylinder opening to inspect the levelness.Finally fix the anchor bolts.
*The sewer shall be arranged rnder the liquor drainage outlet and pressure relief pipe so thet the waste liquor wil be easily discharged along the sewer to avoid splashing to grund,which will be corrosive to the bracket of maching.The sewer location shall be determined by customer according to the site conditions.
*Inspect bolts in every part before adjustment for fastness(especially the bolts and adjusting leading screws of pump bracket).The motor shall be concentric with pump shaft for pump with coupler.
*The installation ot elecric equipment and compressed air control circuilt shal be deteimined by customer according to actual conditions of workshop .However it shall be convenient for the operation withort lffecting the teanspoutation of sarongs.(Note:Keep cable away from the heat source).
Operation
Preparation before operation
*Inspect the location of each pneumatic valve and electric device so as to ensure thet their installation position will be corresponding to each button switch on the control cabinet and ensure the correct pump rotation.
*Do thorough cleaning for the machine with soap bath,soda solution and other suitable wasbing abents.
*In order to avoid bloch on test materials by probable remaining dirt,it is better to dyt deep color first and then dye weak color in the test.
*Fill in required slft water inside the dye bexk and then hoist de cage containing materials to be dyed into the dye beck.Jeat to about 40-50℃ａnd boil for ten minutes.Tske ort the dye cage and discharge teh liquor.
Notes to in operation:
*It is strictly prohibit to open the cover undrr pressurizing comdition or close to discharge liquor vnder normal pressure condition.
*The main pump and auxiliary pump can mot be started when lacking of water.If there is any abnormal noise or other faults in the operation of punp,it shall be stopped immediately for inspection.
Special motes
*Please observe strictly the laws and regulationg stipulated by local labour department or the safety authorityfor pressure containers of boiler,ａnd accept the supervision and inspection by the abovementionsd departments.
*Strictly forbid opening the cover of boiler or respective mauth of pipe in oder to avoid accident.

以上為染色機系統原理示意圖（電器柜面板操作圖）。
Above drawing is the schametic diagram of dyeing machine system(Panel operation diagram of electric cabinet)

GR202系列染色機安裝示意圖Schametic Diagram on installation of GR202

注：以上參數如有更改恕不另外通知，圖示結構和尺寸僅供參考。
Note:The above parameters can be modified without separate notification,The schematic construction and dimension are only als reference.