保溫材料憎水性測定儀

一、保溫材料憎水性測定儀產品簡介：

該儀器主要用于檢測珍珠巖、礦物棉、聚苯乙烯泡沫塑料、硬質聚氨酯泡沫塑料等保溫隔熱制品材料憎水性試驗。將試樣與水平呈450角放置，試樣中間位于噴頭下面給定的位置，用一定的流量的水噴淋試樣至規定時間，通過測量噴淋前后試樣質量的變化，從而計算出試樣中未透水部分的體積百分率。

Product introduction of insulation material hydrophobicity tester:

This instrument is mainly used to test the water-repellency test of thermal insulation products such as perlite, mineral wool, polystyrene foam, rigid polyurethane foam. Place the sample at a 450-degree angle with the center of the sample at a given position under the spray head. Spray the sample with a certain flow of water for a specified time. Calculate the test by measuring the change in sample mass before and after spray Volume percentage of the impervious part of the sample.

二、保溫材料憎水性測定儀技術參數：

1)憎水性測試儀

a.淋水裝置：由金屬?lài)婎^、玻璃轉子流量計及穩壓水源組成，中間用橡皮管連接。金屬?lài)婎^的中間位于試驗面的縱向對稱面上，并可在試樣架上移動。玻璃轉子流量計的流量范圍為10-100L/h，精度2.5級。

b. 試樣架:試樣架以450傾角安置在一個可以調節水平的支座上.

c. 金屬?lài)婎^:噴水面呈凸圓形。其上均布19個Φ0.9mm的孔，當噴頭位于圖1規定的位置上試驗時，試樣受淋面積的橫向尺寸為148mm。

2)天平：A小分度值不大于被稱質量的0.5%。

3)干燥箱。

4)測厚儀：壓板壓力98Pa,分度值0.1mm

5)游標卡尺：測量范圍0-150mm，分度值0.02mm。

6)鋼直尺：測量范圍0-300mm，分度值1mm。

外形尺寸：410X205X590mm

重量：13.5kg

Second, the technical parameters of the insulation material hydrophobicity tester:

1) Hydrophobic tester

a. Water spraying device: It consists of metal nozzle, glass rotor flowmeter and regulated water source, with rubber tube connected in the middle. The middle of the metal nozzle is located on the longitudinal symmetry plane of the test surface and can be moved on the sample holder. The flow range of the glass rotor flowmeter is 10-100L / h, and the accuracy is 2.5 grade.

b. Sample holder: The sample holder is placed on a horizontally adjustable support at an inclination of 450.

c. Metal nozzle: the water spray surface is convexly rounded. Nineteen holes with a diameter of 0.9 mm are evenly distributed thereon. When the nozzle is tested at the position specified in FIG.

2) Balance: A small division value is not more than 0.5% of the weighed mass.

3) Drying box.

4) Thickness gauge: pressure plate pressure 98Pa, division value 0.1mm

5) Vernier caliper: The measuring range is 0-150mm, and the division value is 0.02mm.

6) Steel ruler: Measuring range is 0-300mm, division value is 1mm.

Dimensions: 410X205X590mm

Weight: 13.5kg

三、保溫材料憎水性測定儀操作步驟：

★將試樣放入干燥箱內，在105±50C的溫度下干燥至恒重。當試樣在此溫度下易變形或含有易揮發易變化的組分時，可在60±50C或小于揮發溫度5-100C的條件下干燥至恒重。稱量試樣的質量m1。

★測量干燥后試樣的尺寸。對板狀制品，長度和寬度的測量在試樣的正、反兩面進行，各測4次，讀書**到1mm。軟質制品的厚度測量采用測厚儀，硬質制品的厚度測量采用游標卡尺，沿試樣長度方向均勻地測3個點，讀數**到0.1mm。對管狀制品內、外徑的測量應在試樣的兩端進行，各測4處。長度測量?jì)纱?。讀數**到1mm。試樣各尺寸的測量結果均取平均值。計算出試樣的厚度（或壁厚）及體積。

★將試樣安放在憎水性側試儀上（對單面做憎水處理的試樣，應分別測其兩面的憎水性，對板狀制品，應根據試樣厚度，調節噴頭位置，使其滿足圖1要求。對管狀制品，應使其內表面向下，調節噴頭位置，使試樣上半部分均勻受淋），調節水流量，使其穩定在 1L/min，連續噴淋lh，然后，取下試樣，用皺紋紙快速吸取表面水滴，立即稱量試樣的質量m2。

Third, the operating steps of the insulation material hydrophobicity analyzer:

★ Put the sample in a drying box and dry to constant weight at 105 ± 50C. When the sample is easily deformed or contains components that are volatile and changeable at this temperature, it can be dried to constant weight at 60 ± 50C or 5-100C less than the volatilization temperature. Weigh the sample m1.

★ Measure the size of the sample after drying. For plate-shaped products, the length and width are measured on the front and back sides of the sample, each of which is measured 4 times, and the reading is ** to 1 mm. The thickness of soft products is measured by a thickness gauge, and the thickness of hard products is measured by a vernier caliper. Three points are uniformly measured along the length of the sample, and the reading is ** to 0.1 mm. The inner and outer diameters of the tubular product shall be measured at both ends of the specimen, each at 4 locations. The length was measured twice. Reading ** to 1mm. The measurement results of each size of the sample are averaged. Calculate the thickness (or wall thickness) and volume of the sample.

★ Place the sample on a water-repellent side tester (for a sample that has been treated with water repellency on one side, the water repellency of both sides should be measured separately. For plate products, the nozzle position should be adjusted according to the thickness of the sample to Meet the requirements of Figure 1. For tubular products, the inner surface should be downward, adjust the position of the spray head, so that the upper part of the sample is evenly sprayed), adjust the water flow to stabilize it at 1L / min, and continuously spray for lh, then Remove the sample, use the crepe paper to quickly absorb the water droplets on the surface, and immediately weigh the sample mass m2.

四、保溫材料憎水性測定儀試樣：

板狀制品試樣的尺寸為300mm*150mm，厚度為制品的原厚。管狀制品試樣長300mm，橫截面為半環形或扇形，壁厚為制品的原壁厚。制備試樣時應盡可能使試樣具有代表性，不要從帶有折皺或表面破損的部位取樣。泡沫塑料制品應去除表皮。

Fourth, the insulation material hydrophobicity tester sample:

The size of the plate-shaped product sample is 300mm * 150mm, and the thickness is the original thickness of the product. The sample of the tubular product is 300mm long, the cross section is semi-circular or fan-shaped, and the wall thickness is the original wall thickness of the product. Samples should be prepared as representative as possible, and samples should not be taken from areas with wrinkles or surface damage. Skins should be removed from foam plastic products.

五、保溫材料憎水性測定儀原理：

將試樣與水平呈450角放置，試樣中間位于噴頭下面給定的位置，用一定的流量的水噴淋試樣至規定時間，通過測量噴淋前后試樣質量的變化，從而計算出試樣中未透水部分的體積百分率。

Fifth, the principle of the water-repellent measuring instrument of thermal insulation material:

Place the sample at a 450-degree angle with the center of the sample at a given position under the spray head. Spray the sample with a certain flow of water for a specified time. Calculate the test by measuring the change in sample mass before and after spray Volume percentage of the impervious part of the sample.