燃燒法瀝青含量測定儀特點：
★燃燒爐爐體采用航天隔熱材料制成，預熱時間短，升溫速度快，20分鐘內可至標準工作溫度538℃，與同類產品相比大大節約了試驗時間。
★隔熱性能良好，爐體內部達到標準工作溫度時，爐體外部溫度低于45℃，操作安全性高，同時有效避免了高溫對電子秤精度的影響。
★具有后燃燒室二次燃燒功能，及高溫過濾，排風系統，保證試驗廢氣排放量達到環保要求。
★儀器自動運行，易于操作，只需輸入樣品重量和標定系數，裝入樣品，按工作鍵，試驗結束后自動打印數據。
★軟件功能強大，可同時顯示瀝青含量，油石比，樣品損失重量，試驗時間。
★采用進口天平，保證計量準確。
Combustion method asphalt content tester features:
★ Combustion furnace body is made of aerospace thermal insulation material, with short warm-up time and fast heating speed. It can reach the standard working temperature of 538 ℃ in 20 minutes, which greatly saves test time compared with similar products.
★ Good thermal insulation performance. When the inside of the furnace body reaches the standard working temperature, the outside temperature of the furnace body is lower than 45 ° C, and the operation safety is high. At the same time, the effect of high temperature on the accuracy of the electronic scale is effectively avoided.
★ It has the function of secondary combustion in the post-combustion chamber, as well as high-temperature filtering and exhaust system to ensure that the test exhaust emissions meet environmental protection requirements.
★ The instrument runs automatically and is easy to operate. Just enter the sample weight and calibration coefficient, load the sample, press the work key, and the data will be printed automatically after the test.
★ The software is powerful and can display the asphalt content, oil-stone ratio, sample weight loss and test time at the same time.
★ Imported balance is used to ensure accurate measurement.
燃燒法瀝青含量測定儀技術參數:
★試樣重量：4500g,推薦試樣重量：1000～1500g
★天平精度：±0.1g，天平量程：10Kg
★燃燒室尺寸：長350mm×寬440mm×高330mm
★燃燒室高工作溫度：800℃，標準工作溫度：538℃
★自動檢測測試終點，瀝青含量的測試精度可達0.1%
★試驗時間：20～30分鐘
★電源：工作電壓 380V±10%三相（星形），電流不大于20A
★重量：220KG
★外形尺寸：900x750x1300mm
★功率：6KW
★環境溫度：≤35℃
★相對濕度：≤85%
Technical parameters of combustion method asphalt content tester:
★ Sample weight: 4500g, recommended sample weight: 1000 ～ 1500g
★ Balance accuracy: ± 0.1g, balance range: 10Kg
★ Combustion chamber size: length 350mm x width 440mm x height 330mm
★ High working temperature of combustion chamber: 800 ℃, standard working temperature: 538 ℃
★ Automatic detection of test end point, test accuracy of asphalt content can reach 0.1%
★ Test time: 20 ～ 30 minutes
★ Power supply: working voltage 380V ± 10% three-phase (star), current is not more than 20A
★ Weight: 220KG
★ Dimensions: 900x750x1300mm
★ Power: 6KW
★ Ambient temperature: ≤35 ℃
★ Relative humidity: ≤85%
燃燒法瀝青含量測定儀操作規程：
★檢查試驗室電源是否安全接通。
★檢查單片機電源及燃燒爐電源，接通燃燒爐電源，打開控制機箱右側的紅色開關，使單機片進入工作狀態，顯示屏顯示工作菜單。
★設定溫度（通常為540度），校正參數（初次校正參數為0），混和料類型。
★按下加熱鍵，加熱指示燈亮，燃燒爐開始加熱。
★當爐膛達到設置溫度時，打開燃燒爐爐門，此時加熱自動停止，將空料筐放入托盤（請小心輕放）。
★關上爐門，按下加熱鍵加熱，待顯示屏顯示的時實溫度不低于500度，試樣重量數值（此時為料筐重量）穩定后（此時加熱為3～10min），再按去皮鍵，將試樣重量清0，數值應小于0.2g。（注：必須在去皮重后再打開爐門）
★打開爐門取出料筐，請馬上關上爐門以免爐膛溫度下降，將所需要試驗的瀝青混和料放入料筐內，注意不要堆放在一起要平攤放入料筐內。
★將料筐放入燃燒爐內的托盤上，一定要將料筐放置在托盤的中。才能確保試驗結果的準確性。
★關上爐門，迅速按下加熱鍵，加熱指示燈亮，燃燒爐開始加熱，顯示屏顯示試樣重量（試驗中此數值不變），加熱30s后，風機開始工作，顯示屏上的數值刷新一次，此時試驗開始。
★試驗中顯示屏上不斷的顯示損失重量的數值，當損失的重量達到一定的值時，單機片自動知道試驗是否結束，試驗結束風機自動停止工作后，顯示屏上顯示試驗結果，打印機自動打印試驗報告。
★打開爐門取出料筐并清理干凈，準備下次試驗。
★如需要多份試驗報告，請重復按下打印鍵。
Combustion method for asphalt content tester:
★ Check whether the power of the laboratory is safely connected.
★ Check the power supply of the single-chip microcomputer and the power of the combustion furnace. Turn on the power of the combustion furnace. Turn on the red switch on the right side of the control cabinet to make the single chip enter the working state.
★ Set temperature (usually 540 degrees), calibration parameters (initial calibration parameters are 0), mix type.
★ Press the heating key, the heating indicator lights up, and the combustion furnace starts heating.
★ When the furnace reaches the set temperature, open the door of the combustion furnace, and the heating will automatically stop at this time. Put the empty basket into the tray (please handle it carefully).
★ Close the furnace door, press the heating button to heat, wait until the real temperature displayed on the display is not less than 500 degrees, the sample weight value (in this case, the weight of the basket) is stable (at this time, the heating is 3 to 10 minutes), and then Press the Tare key to clear the sample weight to 0. The value should be less than 0.2g. (Note: the oven door must be opened after tare)
★ Open the furnace door to take out the material basket. Please close the furnace door immediately to prevent the temperature of the furnace from falling. Put the asphalt mixture to be tested into the material basket. Be careful not to stack them together and put them in the material basket.
★ Put the basket on the tray in the combustion furnace. Be sure to place the basket in the tray. In order to ensure the accuracy of the test results.
★ Close the furnace door, quickly press the heating key, the heating indicator lights up, the combustion furnace starts heating, the display shows the sample weight (the value remains unchanged during the test), the fan starts to work after heating for 30s, and the value on the display refreshes once At this point, the test begins.
★ During the test, the value of the weight loss is continuously displayed on the display. When the lost weight reaches a certain value, the stand-alone tablet automatically knows whether the test is over. After the test is completed, the fan automatically stops working. experiment report.
★ Open the furnace door, take out the material basket and clean it, and prepare for the next test.
★ If multiple test reports are required, press the print key repeatedly.
員1.png)
QQ:2568841715
