<tt id="i8i4i"><table id="i8i4i"></table></tt>
  • <li id="i8i4i"><table id="i8i4i"></table></li>
    <blockquote id="i8i4i"></blockquote>
    • <tt id="i8i4i"></tt>

    行業產品

    • 行業產品

    上海鼎徵儀器儀表設備有限公司


    當前位置：上海鼎徵儀器儀表設備有限公司>>蒸汽噴射試驗箱>>ISO16925涂料和清漆. 涂層耐壓力水噴射測試

    ISO16925涂料和清漆. 涂層耐壓力水噴射測試

    返回列表頁
    參  考  價面議
    具體成交價以合同協議為準

    產品型號

    品       牌

    廠商性質其他

    所  在  地上海

    紡織服裝機械網采購部電話：0571-88918531QQ:2568841715

    聯系方式：查看聯系方式

    更新時間：2025-02-11 16:35:19瀏覽次數：18次

    聯系我時，請告知來自 紡織服裝機械網

    經營模式：其他

    商鋪產品：550條

    所在地區：

    聯系人：謝文清

    產品簡介

    產品介紹：

    詳細介紹

    ISO16925涂料和清漆. 涂層耐壓力水噴射測試
    1 Scope
    This International Standard specifies a test method for the assessment of the resistance of coatings to
    pressure water-jetting. The test method simulates the effects pressure water-jetting has on a coating.
    5 Apparatus and materials
    Ordinary laboratory apparatus, together with the following:
    5.1 Pressure water-jet, consisting of a high-pressure pump and a nozzle.
    A high-pressure pump conveys the water from a storage bin. To avoid influences from variations in
    pressure, it is necessary that the pressure and the volumetric flow rate be adjustable at the nozzle
    described below.
    The water temperature shall be adjustable to ± 2 °C.
    The temperature shall be adjusted in accordance with Annex A. Necessary safety devices on the pressure
    side of the unit, as e.g. pressure relief valve and by-pass valve, shall exist. If the jetting is unsteady, a flow
    calming section may be installed in front of the nozzle. A pulsation of the water jet at the opening of the
    pump is inadmissible. In order to reach a reproducible result, the nozzle shall be solidly mechanically
    fixed and the test specimen shall be secured against slipping. For the adjustment of the volumetric flow
    rate, a nozzle with a jet angle of 25° and a volumetric flow rate of 6 l/min at 2 MPa (20 bar) is required
    (see Annex A).
    The following technical data should be attainable:
    — volumetric flow rate: 8 l/min to 14 l/min
    — pressure: 4 MPa (40 bar) to 13 MPa (130 bar)
    — temperature: 20 °C to 80 °C
    — jetting time: 10 s to 300 s


    Figure 1 shows the schematic construction of a pressure water-jet apparatus which is specially built for these tests.
     
    Key
    1 flow calming section
    2 high-pressure valve, height adjustable
    3 test specimen
    4 clamping element  
    5 feed tank
    6 floating valve with filter
    7 water shortage safeguard
    8 heating
    9 base frame, moveable
    10 temperature sensor  
    11 high-pressure pump
    12 by-pass valve  
    13 pressure relief valve
    14 pressure transmitter
    8.1 Introducing the cut or the scribe
    Make sure that the test specimen is securely fastened when introducing the cut or the scribe.
    Introduce both of the cuts or scribes vertically through the coating into the substrate using the cutting
    or scribing tool, as shown in Figure 2. The depth of the cut or scribe into the substrate should be as
    minimal as possible. The length of the first cut or scribe shall be at least 100 mm, if the geometry of the
    part allows that. At an angle, introduce a second cut or scribe with a minimum length of 20 mm. The
    cuts or scribes shall be introduced straight-line at an angle of approximately 30°. An automatic cutting
    or scribing device may be used. Residues of the coating shall be removed from the cut or scribe.
    NOTE The depth of the cut or scribe into the substrate influences the result.
    The cutting or scribing tools should be checked regularly and replaced if necessary.
       Figure 2 — Introducing the cuts or scribes (St Andrew’s cross)

    8.2 Testing
    After inserting the test specimen into the apparatus (e.g. using a spacer block), calibrate the space
    between test specimen and nozzle.
    Operate the pressure water-jetting apparatus at room temperature.
    Three test methods (A, B, or C – see Table 1) are preferred as well as three possible scribing tools (C, L, or
    S – see 5.3). The test method to be applied, the scribing or cutting tool to be used, and the water pressure
    shall be agreed.
    Table 1 — Test methods

    Test method Water Temperature
    ℃    		 Impact angle Space between nozzle and sample （mm） Flow rate
    （L/min）    		 Duration of
    jetting
    A 60±2 90±2 100±1 11.3±0.2 30±1
    B 60±2 90±2 100±1 11.3±0.2 60±1
    C 60±2 90±2 100±1 11.3±0.2 60±1
     
    For jetting, deionized water should be used.
    When using automatic and manual devices, fasten the test specimen so that the water jet impacts as
    shown in Figure 3. The jet impacts in the middle above the point of intersection onto the longer one of both cuts/scribes.

    Figure 3 — Jetting area
    9 Evaluation
    9.1 General
    Damage is recognizable when the coating loosens or flakes, regardless of which coat sustains the damage.
    9.2 Evaluation with pictures to compare
    Carry out the evaluation visually, comparing the specimen with the pictures.
    In the course of the visual evaluation, a characteristic value is laid down by comparing with the
    illustrations in Figures 4 to 9. A characteristic value between 1 and 5 results, depending on the degree
    of damage. No damage corresponds to the characteristic value 0. In addition to the evaluation, if
    applicable, the attribution of the separation from the main separation level or to the respective film
    shall be indicated.
    The result of the visual assessment is indicated in dependence of the applied method, for example:
    — method A: characteristic value A;
    — method B: characteristic value B;
    — method C: characteristic value C.
    NOTE In addition, by measuring the areas of flaking (maximum width, in millimetres, or area, in square
    millimetres), the overall damage can be evaluated. The overall damage is calculated by summing up all damaged
    areas of the test specimen. Even the smallest areas of flaking are measured and calculated, and all areas added to
    the overall damage.

    Figure 5 — Characteristic value 1 for pressure water-jet damage

    Figure 6 — Characteristic value 2 for pressure water-jet damage


    Figure 7 — Characteristic value 3 for pressure water-jet damage

    Figure 8 — Characteristic value 4 for pressure water-jet damage

    Figure 9 — Characteristic value 5 for pressure water-jet damage

     
    Annex A
    (normative)
    Calibration of the test apparatus
    A.1 Apparatus and materials
    Ordinary laboratory apparatus, as well as the following.
    A.1.1 Temperature measuring device, with sensor, capable of measuring to 0,5 °C.
    A.1.2 Balance, weighing to 10 g.
    A.1.3 Time measuring device (swatch), capable of measuring ± 0,1 s.
    A.1.4 Container, for the determination of the volumetric flow rate for at least 20 l of water.
    A.1.5 Plastic block, made of polystyrene rigid plastic foam.
    The kind of the polystyrene rigid plastic foam shall be agreed by the interested parties.
    A.1.6 Length measuring device, capable of measuring ± 0,1 mm.
    A.2.4 Calibration of the water jet
    The conditions for the calibration of the jetting are in accordance with method B. For the calibration of
    the jetting, a stainless steel precision flat film extrusion die with a volumetric flow rate of the nozzle of
    6 l/min at 2 MPa (20 bar) and a jet angle 25° is used. This nozzle is required to produce an even liquid
    distribution during the entire jetting.
    When using an automatic pressure-water apparatus, fasten the polystyrene rigid plastic foam in the
    apparatus so that the jet cannot move the block. When using a manual apparatus, fasten the block in a
    similar fixture.
    After jetting, the length and the width of the impact are measured. See Figure A.1.
    The mean length of the impact shall be (73 ± 5) mm and the mean width (8 ± 1) mm on average.


    Figure A.1 — Measures of the washed-out areas in the polystyrene rigid plastic foam
    蒸汽噴射試驗機滿足測試規范汽車廠家：寶馬、奔馳、通用、大眾、福特、沃爾沃等規范（AA-0136、DIN 55662、ISO16925，DBL 7381，GM9531P、PV1503、VOLVO STD 423-0015，VOLVO VCS 1029 54719、FLTM BO 160-04、MS210-07，PSA D23 5376，Renault D25 2018/-A-2001 ，GMW16745-2012方法B，TPJLR-52.561-2009） 


    您感興趣的產品PRODUCTS YOU ARE INTERESTED IN

    紡織服裝機械網 設計制作，未經允許翻錄必究 .? ? ? Copyright(C)?2021 http://www.lcservicesllc.com,All rights reserved.

    以上信息由企業自行提供，信息內容的真實性、準確性和合法性由相關企業負責，紡織服裝機械網對此不承擔任何保證責任。 溫馨提示：為規避購買風險，建議您在購買產品前務必確認供應商資質及產品質量。

    會(huì )員登錄

    ×

    請輸入賬號

    請輸入密碼

    =

    請輸驗證碼

    收藏該商鋪

    請 登錄 后再收藏

    提示

    您的留言已提交成功！我們將在第一時間回復您~
    色欲综合久久躁天天躁_亚洲欧美另类激情综合区蜜芽_久久99国产综合精品女同_最近最好的2019中文日本字幕