P-A0、P-B0小軋車 P-A0、P-B0 small padder
概述:
如今客戶對產品質量要求日之趨高，除了要求對色準，外觀平整外，尤其在手感方面要求越來越高。往往因手感達不到要求而重做的，從而導致時間和精力的嚴重浪費。我司的小軋車剛好可以很好的解決這個問題，可利于貴司模擬現場條件制做高度再現性的正確手感樣布爭取更好的商機。
General:
Nowadays , customers ask for more requirements about product quality :not only the requirement of color and smooth surfaces, but also comfortable feel. Some work should be redone because of bad touching, which in turn , results in serious waste of time and energy. The small padder manufactured by our company is an ideal solution to this problem . Excellent and comfortable touching can be reached with the on spot simulating in your company so as to create more and better business opportunities for you 。
用途：
可調整到與現場一致的壓吸率。
可利用此機，選擇整理助劑濃度的品質好壞．適用于染整廠、助劑、顏料制造廠。
Application:
Adjustable to pressed absorbing rate on spot and provide precise pressed dyeing or resin prescription.
Select the concentration quality of auxiliary ,which is applicable for dyeing and finishing plant , manufacturer of auxiliary and dye .
特點：
1.以壓縮空氣推動氣缸．使壓力均衡，且經久使用后，壓力的再現性良好。
2.羅拉目前的使用硬度72度，壓吸率在45%～90%之間適用布范圍廣，應用廣泛。
3.小軋車要業安全性能佳，馬達轉動加裝正反轉功能，轉動控制可用手動或腳動來互換控制，對操作者安全．特殊裝置效率高又安全不會(huì )夾到手指。除主架外，其他是不銹鋼制成。
Feature:
1.To promote the membrane by compressing the air; make the pressure balanced .The pressure reappearance is still in good working order after long time using.
2.The hardness of roller is 72 degree and pressure-absorbing rate is from 45% to 90%.
With better safety and reciprocal rotating of motor ,the small padder can be operated either by hａnd or foot ,which makes the operator much safer . 3.The special device with high efficiency is designed for safe operation and used to prevent the finger to be clamped. All the other parts are made of stainless steel except the framework .
規格：
1.壓吸羅拉采用進口材料，外部被覆N，B，R，橡膠再加以精密研磨完成，硬度為邵氏72度。
2.橡膠羅拉直徑為130mm，長度為430mm。
3.采用3相370V電機轉動，轉速可調節。
4.左右壓力可獨立調整，壓力范圍0～7kg
5.二組壓力指示計
6.二組壓力調節閥
7.空壓機為選購設備
8.外形尺寸（L*W*H)：P-A0：920*650*1250
P-B0：870*650*1100
Specification：
1.Pressure absorbing roller with 72 degree of hardness , is made of imported materials and covered by N,B,R, and rubber ; then be abraded.
2.The diameter of rubber roller is 130mm and the length is 430mm.
3.The phase 370Vmotor rotation,speed adjustable.
4.Right and left pressure or independent adjustment with the pressure range between 0~7kg.
5.Group two pressure indicating meter
6.Group two pressure adjustment valve
7.Air compressor is an optional equipment
8.Pimensions（L*W*H)：P-A0：920*650*1250
P-B0：870*650*1100
所列規格如有變動，本公司擁有隨時更改權，恕不另行通知。
If the listed specification has any changes,our company has right to modify without notification at any time.
