產品名稱：GA5-1帆布、皮革厚料縫紉機
產品圖片：
適用范圍：
適用于縫制厚料帆布、皮革制品如貨車篷帆、載重袋、安全帶、馬鞍、箱包等厚料制品的縫制。
。
Applicable Scope:
Suitable for sewing thick canvas, leather goods such as freight car sail, load bags, safety belts, saddles, suitcases and so on.
.
機器的使用與保養：
1、機器在裝箱強，為防止機件生銹，涂有防銹油脂，由于貯藏和運輸，可能造成油脂硬化和積聚灰塵，使用前必須將表面的油脂用汽油清洗干凈，并用潔凈的棉紗或軟布干。
2、機器在運轉前，必須對各處油孔加注縫紉機油，然后再開空車試運轉。手輪旋轉方向為逆時針?lè )较颍ú僮髡呙嫦蚴州啠?。機器在正常使用時，要時常加注潤滑油，每班不得少于兩次。
3、機器的工作速度按操作者的熟練程度而異，新機器安裝后，應有一段低速磨合階段，按800轉/分鐘運轉一個月后，再加快到額定轉速，但不得超過1000轉/分鐘，以免因轉速過高引起機件損傷，影響機器的使用壽命。
Machine operation and maintenance:
1, the machine is strong in packing, in order to prevent rust, coated with anti-rust grease, due to storage and transportation, may cause oil hardening and dust accumulation, the surface of oil must be cleaned with gasoline, and clean cotton yarn or soft cloth dry.
2. Before the operation of the machine, the oil of the sewing machine must be filled with oil at all oil holes, and then the machine should be tested in an empty car. The rotation direction of the handwheel is counterclockwise (the operator faces the handwheel). When the machine is in normal use, lubricants should be filled from time to time, not less than twice per shift.
3, the working speed of the machine varies according to the operator's proficiency, after the installation of the new machine, there should be a period of low speed runin stage, run at 800 RPM for a month, then speed up to the rated speed, but not more than 1000 RPM, in order to avoid damage caused by too high speed parts, affect the service life of the machine.
技術規格Technical specifications：
縫紉轉數 Maximum sewing revolution | 800針/min |
最長針距 stitch | 7mm |
壓腳提升高度 Presser foot ascend | 12mm |
機針右側面工作空間 | 268mm*166mm |
機頭外形（長*寬*高） | 530mm*270mm*480mm |
機頭凈重 The nose of | 35kg |
電動機功率 Motor power | 550w |
采用機針 The needle | GA*1型(type)，NM140-230 |
縫線規格 Thread specification | 21-32tex*3-7(25-18支/3-7股）臘線wax，化纖線 |
