上海榮計達儀器科技有限公司**經營水泥實驗儀器、混凝土實驗儀器、公路土工實驗儀器、干粉砂漿保溫砂漿實驗儀器、瀝青防水材料實驗儀器、油漆涂料實驗儀器、無損檢測等實驗儀器。**經營水泥實驗儀器、混凝土實驗儀器、公路土工實驗儀器、干粉砂漿保溫砂漿實驗儀器、瀝青防水材料實驗儀器、油漆涂料實驗儀器、無損檢測等實驗儀器。公司產品憑借過硬的質量、完善的售后服務、合理的價格各大院校、檢測單位、建材企業、工程建設單位。在消費者當中享有較高的地位和良好的口碑，用戶遍布國內近三十個省市、自治區，并遠銷國外，與用戶建立了長期穩定的合作關系。公司實力雄厚，重信用、守合同。有健全的管理制度和完善健全的質量管理體系。并有反應迅速、服務周到的售后服務系統。我們將不懈努力、一如既往以?xún)?yōu)異的品質為客戶服務。
Shanghai Rongjida Instrument Technology Co., Ltd. ** operates cement experiment equipment, concrete experiment equipment, highway geotechnical experiment equipment, dry mortar thermal insulation mortar experiment equipment, asphalt waterproof material experiment equipment, paint coating experiment equipment, non-destructive testing and other experimental equipment. ** Operating cement experiment equipment, concrete experiment equipment, highway geotechnical experiment equipment, dry mortar thermal insulation mortar experiment equipment, asphalt waterproof material experiment equipment, paint coating experiment equipment, non-destructive testing and other experimental equipment. Company products rely on excellent quality, perfect after-sales service, reasonable prices sell well in major universities, testing units, building materials enterprises, engineering construction units. It enjoys a high status and a good reputation among consumers, and has customers in nearly 30 provinces, cities, and autonomous regions in China, and has been exported to foreign countries. It has established long-term and stable cooperative relationships with users. The strength of the company, credit and contract compliance. Have a sound management system and a sound quality management system. And has a responsive and thoughtful after-sales service system. We will make unremitting efforts to serve our customers with excellent quality as always.
涂層耐溶劑測定儀是**檢測儀器，用于測定鋁塑復合板及類似底材上涂層的耐溶劑性，在規定的溶劑和條件下擦洗涂層后，目測擦洗處是否有顯露底材現象。
Coating solvent resistance tester is a testing instrument for measuring the solvent resistance of coatings on aluminum-plastic composite boards and similar substrates. After scrubbing the coating under the specified solvents and conditions, visually inspect whether there is a exposed bottom in the scrubbing area. Material phenomenon.
涂層耐溶劑測定儀技術參數：
★擦洗行程：100mm
★擦洗頻率：100次/min
★擦洗力:1000±100g
★擦洗頭面積：2cm2
Coating solvent resistance tester technical parameters:
★ Scour stroke: 100mm
★ Scrubbing frequency: 100 times / min
Scrubbing power: 1000 ± 100g
★ Scour head area: 2cm2
涂層耐溶劑測定儀使用說明：
★接通電源，打開電源開關，按標準要求設定涂擦次數，按動置數開關，使計數顯示設定值，然后按動啟動開關，儀器將開始工作，（若打開電源后，有數值顯示，請按復位開關）計數顯示開始工作，到設定值時，儀器自動停止工作，若需要中途停機，按動暫停開關即停。
★按動復位開關將刷子臂連同部件卸下，取出試樣，目測擦洗處是否有顯露內層（即是否有露底）現象以三塊試樣中性能**差著為試驗結果。
Instructions for coating solvent resistance tester:
★ Turn on the power, turn on the power switch, set the number of rubbing times according to the standard requirements, press the set switch to make the count display the set value, and then press the start switch, the instrument will start to work (if there is a value after turning on the power Display, please press the reset switch) The counting display starts to work. When the set value is reached, the instrument will automatically stop working. If you need to stop midway, press the pause switch to stop.
★ Press the reset switch to remove the brush arm and its components, remove the sample, and visually inspect the scrubbing area to reveal whether the inner layer (that is, whether there is a bottom) is exposed. The performance of the three samples is the worst.
涂層耐溶劑測定儀注意事項：
★儀器在正常工作中，計數器不得隨意設定。
★儀器應水平放置后方可作試驗。
★儀器使用較長時間后應將儀器上蓋部件拆開，向變速箱內注入機油。在兩導杠的油孔中亦注入機油，但不應過量。
★試驗完畢后，應將剩余溶劑倒出，其余部分擦洗干凈，以防生銹。
Note for coating solvent resistance tester:
★ In normal operation of the instrument, the counter must not be set arbitrarily.
★ The instrument should be placed horizontally before testing.
★ After using the instrument for a long time, the upper cover parts of the instrument should be disassembled, and oil should be injected into the gearbox. Oil is also injected into the oil holes of the two guide bars, but it should not be excessive.
★ After the test is completed, the remaining solvent should be poured out, and the rest should be scrubbed to prevent rust.
